USB: pl2303: add ids for Hewlett-Packard HP POS pole displays

commit b16c02fbfb963fa2941b7517ebf1f8a21946775e upstream.

Add device ids to pl2303 for the Hewlett-Packard HP POS pole displays:

LD960: 03f0:0B39
LCM220: 03f0:3139
LCM960: 03f0:3239

[ Johan: fix indentation and sort PIDs numerically ]

Signed-off-by: Aaron Sanders <aaron.sanders@hp.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb

commit 1f81b6d22a5980955b01e08cf27fb745dc9b686f upstream.

We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.

The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.

This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.

This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747146ea97efa18e04576acd3416e2514f5 "USB: xhci: URB
cancellation support."

Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ext4: use i_size_read in ext4_unaligned_aio()

commit 6e6358fc3c3c862bfe9a5bc029d3f8ce43dc9765 upstream.

We haven't taken i_mutex yet, so we need to use i_size_read().

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ext4: move ext4_update_i_disksize() into mpage_map_and_submit_extent()

commit 622cad1325e404598fe3b148c3fa640dbaabc235 upstream.

The function ext4_update_i_disksize() is used in only one place, in
the function mpage_map_and_submit_extent().  Move its code to simplify
the code paths, and also move the call to ext4_mark_inode_dirty() into
the i_data_sem's critical region, to be consistent with all of the
other places where we update i_disksize.  That way, we also keep the
raw_inode's i_disksize protected, to avoid the following race:

      CPU #1                                 CPU #2

   down_write(&i_data_sem)
   Modify i_disk_size
   up_write(&i_data_sem)
                                        down_write(&i_data_sem)
                                        Modify i_disk_size
                                        Copy i_disk_size to on-disk inode
                                        up_write(&i_data_sem)
   Copy i_disk_size to on-disk inode

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ext4: fix jbd2 warning under heavy xattr load

commit ec4cb1aa2b7bae18dd8164f2e9c7c51abcf61280 upstream.

When heavily exercising xattr code the assertion that
jbd2_journal_dirty_metadata() shouldn't return error was triggered:

WARNING: at /srv/autobuild-ceph/gitbuilder.git/build/fs/jbd2/transaction.c:1237
jbd2_journal_dirty_metadata+0x1ba/0x260()

CPU: 0 PID: 8877 Comm: ceph-osd Tainted: G    W 3.10.0-ceph-00049-g68d04c9 #1
Hardware name: Dell Inc. PowerEdge R410/01V648, BIOS 1.6.3 02/07/2011
 ffffffff81a1d3c8 ffff880214469928 ffffffff816311b0 ffff880214469968
 ffffffff8103fae0 ffff880214469958 ffff880170a9dc30 ffff8802240fbe80
 0000000000000000 ffff88020b366000 ffff8802256e7510 ffff880214469978
Call Trace:
 [<ffffffff816311b0>] dump_stack+0x19/0x1b
 [<ffffffff8103fae0>] warn_slowpath_common+0x70/0xa0
 [<ffffffff8103fb2a>] warn_slowpath_null+0x1a/0x20
 [<ffffffff81267c2a>] jbd2_journal_dirty_metadata+0x1ba/0x260
 [<ffffffff81245093>] __ext4_handle_dirty_metadata+0xa3/0x140
 [<ffffffff812561f3>] ext4_xattr_release_block+0x103/0x1f0
 [<ffffffff81256680>] ext4_xattr_block_set+0x1e0/0x910
 [<ffffffff8125795b>] ext4_xattr_set_handle+0x38b/0x4a0
 [<ffffffff810a319d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff81257b32>] ext4_xattr_set+0xc2/0x140
 [<ffffffff81258547>] ext4_xattr_user_set+0x47/0x50
 [<ffffffff811935ce>] generic_setxattr+0x6e/0x90
 [<ffffffff81193ecb>] __vfs_setxattr_noperm+0x7b/0x1c0
 [<ffffffff811940d4>] vfs_setxattr+0xc4/0xd0
 [<ffffffff8119421e>] setxattr+0x13e/0x1e0
 [<ffffffff811719c7>] ? __sb_start_write+0xe7/0x1b0
 [<ffffffff8118f2e8>] ? mnt_want_write_file+0x28/0x60
 [<ffffffff8118c65c>] ? fget_light+0x3c/0x130
 [<ffffffff8118f2e8>] ? mnt_want_write_file+0x28/0x60
 [<ffffffff8118f1f8>] ? __mnt_want_write+0x58/0x70
 [<ffffffff811946be>] SyS_fsetxattr+0xbe/0x100
 [<ffffffff816407c2>] system_call_fastpath+0x16/0x1b

The reason for the warning is that buffer_head passed into
jbd2_journal_dirty_metadata() didn't have journal_head attached. This is
caused by the following race of two ext4_xattr_release_block() calls:

CPU1                                CPU2
ext4_xattr_release_block()          ext4_xattr_release_block()
lock_buffer(bh);
/* False */
if (BHDR(bh)->h_refcount == cpu_to_le32(1))
} else {
  le32_add_cpu(&BHDR(bh)->h_refcount, -1);
  unlock_buffer(bh);
                                    lock_buffer(bh);
                                    /* True */
                                    if (BHDR(bh)->h_refcount == cpu_to_le32(1))
                                      get_bh(bh);
                                      ext4_free_blocks()
                                        ...
                                        jbd2_journal_forget()
                                          jbd2_journal_unfile_buffer()
                                          -> JH is gone
  error = ext4_handle_dirty_xattr_block(handle, inode, bh);
  -> triggers the warning

We fix the problem by moving ext4_handle_dirty_xattr_block() under the
buffer lock. Sadly this cannot be done in nojournal mode as that
function can call sync_dirty_buffer() which would deadlock. Luckily in
nojournal mode the race is harmless (we only dirty already freed buffer)
and thus for nojournal mode we leave the dirtying outside of the buffer
lock.

Reported-by: Sage Weil <sage@inktank.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ext4: note the error in ext4_end_bio()

commit 9503c67c93ed0b95ba62d12d1fd09da6245dbdd6 upstream.

ext4_end_bio() currently throws away the error that it receives.  Chances
are this is part of a spate of errors, one of which will end up getting
the error returned to userspace somehow, but we shouldn't take that risk.
Also print out the errno to aid in debug.

Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ext4: FIBMAP ioctl causes BUG_ON due to handle EXT_MAX_BLOCKS

commit 4adb6ab3e0fa71363a5ef229544b2d17de6600d7 upstream.

When we try to get 2^32-1 block of the file which has the extent
(ee_block=2^32-2, ee_len=1) with FIBMAP ioctl, it causes BUG_ON
in ext4_ext_put_gap_in_cache().

To avoid the problem, ext4_map_blocks() needs to check the file logical block
number. ext4_ext_put_gap_in_cache() called via ext4_map_blocks() cannot
handle 2^32-1 because the maximum file logical block number is 2^32-2.

Note that ext4_ind_map_blocks() returns -EIO when the block number is invalid.
So ext4_map_blocks() should also return the same errno.

Signed-off-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

clk: s2mps11: Fix possible NULL pointer dereference

commit 238e14055da87d0d012257788e39fe0df3a82226 upstream.

If parent device does not have of_node set the s2mps11_clk_parse_dt()
returned NULL. This NULL was later passed to of_clk_add_provider() which
dereferenced it in pr_debug() call.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ocfs2: fix panic on kfree(xattr->name)

commit f81c20158f8d5f7938d5eb86ecc42ecc09273ce6 upstream.

Commit 9548906b2bb7 ('xattr: Constify ->name member of "struct xattr"')
missed that ocfs2 is calling kfree(xattr->name).  As a result, kernel
panic occurs upon calling kfree(xattr->name) because xattr->name refers
static constant names.  This patch removes kfree(xattr->name) from
ocfs2_mknod() and ocfs2_symlink().

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Tested-by: Tariq Saeed <tariq.x.saeed@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ocfs2: do not put bh when buffer_uptodate failed

commit f7cf4f5bfe073ad792ab49c04f247626b3e38db6 upstream.

Do not put bh when buffer_uptodate failed in ocfs2_write_block and
ocfs2_write_super_or_backup, because it will put bh in b_end_io.
Otherwise it will hit a warning "VFS: brelse: Trying to free free
buffer".

Signed-off-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ocfs2: dlm: fix recovery hung

commit ded2cf71419b9353060e633b59e446c42a6a2a09 upstream.

There is a race window in dlm_do_recovery() between dlm_remaster_locks()
and dlm_reset_recovery() when the recovery master nearly finish the
recovery process for a dead node.  After the master sends FINALIZE_RECO
message in dlm_remaster_locks(), another node may become the recovery
master for another dead node, and then send the BEGIN_RECO message to
all the nodes included the old master, in the handler of this message
dlm_begin_reco_handler() of old master, dlm->reco.dead_node and
dlm->reco.new_master will be set to the second dead node and the new
master, then in dlm_reset_recovery(), these two variables will be reset
to default value.  This will cause new recovery master can not finish
the recovery process and hung, at last the whole cluster will hung for
recovery.

old recovery master:                                 new recovery master:
dlm_remaster_locks()
                                                  become recovery master for
                                                  another dead node.
                                                  dlm_send_begin_reco_message()
dlm_begin_reco_handler()
{
 if (dlm->reco.state & DLM_RECO_STATE_FINALIZE) {
  return -EAGAIN;
 }
 dlm_set_reco_master(dlm, br->node_idx);
 dlm_set_reco_dead_node(dlm, br->dead_node);
}
dlm_reset_recovery()
{
 dlm_set_reco_dead_node(dlm, O2NM_INVALID_NODE_NUM);
 dlm_set_reco_master(dlm, O2NM_INVALID_NODE_NUM);
}
                                                  will hang in dlm_remaster_locks() for
                                                  request dlm locks info

Before send FINALIZE_RECO message, recovery master should set
DLM_RECO_STATE_FINALIZE for itself and clear it after the recovery done,
this can break the race windows as the BEGIN_RECO messages will not be
handled before DLM_RECO_STATE_FINALIZE flag is cleared.

A similar race may happen between new recovery master and normal node
which is in dlm_finalize_reco_handler(), also fix it.

Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ocfs2: dlm: fix lock migration crash

commit 34aa8dac482f1358d59110d5e3a12f4351f6acaa upstream.

This issue was introduced by commit 800deef3f6f8 ("ocfs2: use
list_for_each_entry where benefical") in 2007 where it replaced
list_for_each with list_for_each_entry.  The variable "lock" will point
to invalid data if "tmpq" list is empty and a panic will be triggered
due to this.  Sunil advised reverting it back, but the old version was
also not right.  At the end of the outer for loop, that
list_for_each_entry will also set "lock" to an invalid data, then in the
next loop, if the "tmpq" list is empty, "lock" will be an stale invalid
data and cause the panic.  So reverting the list_for_each back and reset
"lock" to NULL to fix this issue.

Another concern is that this seemes can not happen because the "tmpq"
list should not be empty.  Let me describe how.

old lock resource owner(node 1):                                  migratation target(node 2):
image there's lockres with a EX lock from node 2 in
granted list, a NR lock from node x with convert_type
EX in converting list.
dlm_empty_lockres() {
 dlm_pick_migration_target() {
   pick node 2 as target as its lock is the first one
   in granted list.
 }
 dlm_migrate_lockres() {
   dlm_mark_lockres_migrating() {
     res->state |= DLM_LOCK_RES_BLOCK_DIRTY;
     wait_event(dlm->ast_wq, !dlm_lockres_is_dirty(dlm, res));
 //after the above code, we can not dirty lockres any more,
     // so dlm_thread shuffle list will not run
                                                                   downconvert lock from EX to NR
                                                                   upconvert lock from NR to EX
<<< migration may schedule out here, then
<<< node 2 send down convert request to convert type from EX to
<<< NR, then send up convert request to convert type from NR to
<<< EX, at this time, lockres granted list is empty, and two locks
<<< in the converting list, node x up convert lock followed by
<<< node 2 up convert lock.

 // will set lockres RES_MIGRATING flag, the following
 // lock/unlock can not run
     dlm_lockres_release_ast(dlm, res);
   }

   dlm_send_one_lockres()
                                                                 dlm_process_recovery_data()
                                                                   for (i=0; i<mres->num_locks; i++)
                                                                     if (ml->node == dlm->node_num)
                                                                       for (j = DLM_GRANTED_LIST; j <= DLM_BLOCKED_LIST; j++) {
                                                                        list_for_each_entry(lock, tmpq, list)
                                                                        if (lock) break; <<< lock is invalid as grant list is empty.
                                                                       }
                                                                       if (lock->ml.node != ml->node)
                                                                         BUG() >>> crash here
 }

I see the above locks status from a vmcore of our internal bug.

Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com>
Cc: Sunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

xattr: guard against simultaneous glibc header inclusion

commit ea1a8217b06b41b31a2b60b0b83f75c77ef9c873 upstream.

If the glibc xattr.h header is included after the uapi header,
compilation fails due to an enum re-using a #define from the uapi
header.

Protect against this by guarding the define and enum inclusions against
each other.

(See https://lists.debian.org/debian-glibc/2014/03/msg00029.html
and https://sourceware.org/glibc/wiki/Synchronizing_Headers
for more information.)

Signed-off-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Allan McRae <allan@archlinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mm: hugetlb: fix softlockup when a large number of hugepages are freed.

commit 55f67141a8927b2be3e51840da37b8a2320143ed upstream.

When I decrease the value of nr_hugepage in procfs a lot, softlockup
happens.  It is because there is no chance of context switch during this
process.

On the other hand, when I allocate a large number of hugepages, there is
some chance of context switch.  Hence softlockup doesn't happen during
this process.  So it's necessary to add the context switch in the
freeing process as same as allocating process to avoid softlockup.

When I freed 12 TB hugapages with kernel-2.6.32-358.el6, the freeing
process occupied a CPU over 150 seconds and following softlockup message
appeared twice or more.

$ echo 6000000 > /proc/sys/vm/nr_hugepages
$ cat /proc/sys/vm/nr_hugepages
6000000
$ grep ^Huge /proc/meminfo
HugePages_Total:   6000000
HugePages_Free:    6000000
HugePages_Rsvd:        0
HugePages_Surp:        0
Hugepagesize:       2048 kB
$ echo 0 > /proc/sys/vm/nr_hugepages

BUG: soft lockup - CPU#16 stuck for 67s! [sh:12883] ...
Pid: 12883, comm: sh Not tainted 2.6.32-358.el6.x86_64 #1
Call Trace:
  free_pool_huge_page+0xb8/0xd0
  set_max_huge_pages+0x128/0x190
  hugetlb_sysctl_handler_common+0x113/0x140
  hugetlb_sysctl_handler+0x1e/0x20
  proc_sys_call_handler+0x97/0xd0
  proc_sys_write+0x14/0x20
  vfs_write+0xb8/0x1a0
  sys_write+0x51/0x90
  __audit_syscall_exit+0x265/0x290
  system_call_fastpath+0x16/0x1b

I have not confirmed this problem with upstream kernels because I am not
able to prepare the machine equipped with 12TB memory now.  However I
confirmed that the amount of decreasing hugepages was directly
proportional to the amount of required time.

I measured required times on a smaller machine.  It showed 130-145
hugepages decreased in a millisecond.

  Amount of decreasing     Required time      Decreasing rate
  hugepages                     (msec)         (pages/msec)
  ------------------------------------------------------------
  10,000 pages == 20GB         70 -  74          135-142
  30,000 pages == 60GB        208 - 229          131-144

It means decrement of 6TB hugepages will trigger softlockup with the
default threshold 20sec, in this decreasing rate.

Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mm: try_to_unmap_cluster() should lock_page() before mlocking

commit 57e68e9cd65b4b8eb4045a1e0d0746458502554c upstream.

A BUG_ON(!PageLocked) was triggered in mlock_vma_page() by Sasha Levin
fuzzing with trinity.  The call site try_to_unmap_cluster() does not lock
the pages other than its check_page parameter (which is already locked).

The BUG_ON in mlock_vma_page() is not documented and its purpose is
somewhat unclear, but apparently it serializes against page migration,
which could otherwise fail to transfer the PG_mlocked flag.  This would
not be fatal, as the page would be eventually encountered again, but
NR_MLOCK accounting would become distorted nevertheless.  This patch adds
a comment to the BUG_ON in mlock_vma_page() and munlock_vma_page() to that
effect.

The call site try_to_unmap_cluster() is fixed so that for page !=
check_page, trylock_page() is attempted (to avoid possible deadlocks as we
already have check_page locked) and mlock_vma_page() is performed only
upon success.  If the page lock cannot be obtained, the page is left
without PG_mlocked, which is again not a problem in the whole unevictable
memory design.

Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mm: page_alloc: spill to remote nodes before waking kswapd

commit 3a025760fc158b3726eac89ee95d7f29599e9dfa upstream.

On NUMA systems, a node may start thrashing cache or even swap anonymous
pages while there are still free pages on remote nodes.

This is a result of commits 81c0a2bb515f ("mm: page_alloc: fair zone
allocator policy") and fff4068cba48 ("mm: page_alloc: revert NUMA aspect
of fair allocation policy").

Before those changes, the allocator would first try all allowed zones,
including those on remote nodes, before waking any kswapds.  But now,
the allocator fastpath doubles as the fairness pass, which in turn can
only consider the local node to prevent remote spilling based on
exhausted fairness batches alone.  Remote nodes are only considered in
the slowpath, after the kswapds are woken up.  But if remote nodes still
have free memory, kswapd should not be woken to rebalance the local node
or it may thrash cash or swap prematurely.

Fix this by adding one more unfair pass over the zonelist that is
allowed to spill to remote nodes after the local fairness pass fails but
before entering the slowpath and waking the kswapds.

This also gets rid of the GFP_THISNODE exemption from the fairness
protocol because the unfair pass is no longer tied to kswapd, which
GFP_THISNODE is not allowed to wake up.

However, because remote spills can be more frequent now - we prefer them
over local kswapd reclaim - the allocation batches on remote nodes could
underflow more heavily.  When resetting the batches, use
atomic_long_read() directly instead of zone_page_state() to calculate the
delta as the latter filters negative counter values.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

sh: fix format string bug in stack tracer

commit a0c32761e73c9999cbf592b702f284221fea8040 upstream.

Kees reported the following error:

   arch/sh/kernel/dumpstack.c: In function 'print_trace_address':
   arch/sh/kernel/dumpstack.c:118:2: error: format not a string literal and no format arguments [-Werror=format-security]

Use the "%s" format so that it's impossible to interpret 'data' as a
format string.

Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reported-by: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mtip32xx: Unmap the DMA segments before completing the IO request

commit 368c89d7ac70f937c93cd6f3b65bcfdfb3ba794f upstream.

If the buffers are unmapped after completing a request, then stale data
might be in the request.

Signed-off-by: Felipe Franciosi <felipe@paradoxo.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mtip32xx: Set queue bounce limit

commit 1044b1bb9278f2e656a1a7b63dc24a59506540aa upstream.

We need to set the queue bounce limit during the device initialization to
prevent excessive bouncing on 32 bit architectures.

Signed-off-by: Felipe Franciosi <felipe@paradoxo.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

USB: unbind all interfaces before rebinding any

commit 6aec044cc2f5670cf3b143c151c8be846499bd15 upstream.

When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.

The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled.  If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.

This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.

The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: "Poulain, Loic" <loic.poulain@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210

commit ead5178bf442dbae4008ee54bf4f66a1f6a317c9 upstream.

Add new ulpi IDs which are available on Xilinx Zynq boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

hvc: ensure hvc_init is only ever called once in hvc_console.c

commit f76a1cbed18c86e2d192455f0daebb48458965f3 upstream.

Commit 3e6c6f630a5282df8f3393a59f10eb9c56536d23 ("Delay creation of
khcvd thread") moved the call of hvc_init from being a device_initcall
into hvc_alloc, and used a non-null hvc_driver as indication of whether
hvc_init had already been called.

The problem with this is that hvc_driver is only assigned a value
at the bottom of hvc_init, and so there is a window where multiple
hvc_alloc calls can be in progress at the same time and hence try
and call hvc_init multiple times.  Previously the use of device_init
guaranteed that hvc_init was only called once.

This manifests itself as sporadic instances of two hvc_init calls
racing each other, and with the loser of the race getting -EBUSY
from tty_register_driver() and hence that virtual console fails:

    Couldn't register hvc console driver
    virtio-ports vport0p1: error -16 allocating hvc for port

Here we add an atomic_t to guarantee we'll never run hvc_init twice.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 3e6c6f630a52 ("Delay creation of khcvd thread")
Reported-by: Jim Somerville <Jim.Somerville@windriver.com>
Tested-by: Jim Somerville <Jim.Somerville@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: musb: avoid NULL pointer dereference

commit eee3f15d5f1f4f0c283dd4db67dc1b874a2852d1 upstream.

instead of relying on the otg pointer, which
can be NULL in certain cases, we can use the
gadget and host pointers we already hold inside
struct musb.

Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: dwc3: fix randconfig build errors

commit 610183051d8f9421f138c4203ca894387f9f8839 upstream.

commit 388e5c5 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.

Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: dwc3: fix wrong bit mask in dwc3_event_devt

commit 06f9b6e59661cee510b04513b13ea7927727d758 upstream.

Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.

Because of that, what used to be 8 bits long, has become 9 bits long.

Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.

So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits

This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.

[ balbi@ti.com : improve commit log a bit ]

Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: media: gspca: sn9c20x: add ID for Genius Look 1320 V2

commit 61f0319193c44adbbada920162d880b1fdb3aeb3 upstream.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: omap3isp: preview: Fix the crop margins

commit 8b57b9669aa884ac75b8d09c251d6b1755533c15 upstream.

Commit 3fdfedaaa "[media] omap3isp: preview: Lower the crop margins"
accidentally changed the previewer's cropping, causing the previewer
to miss four pixels on each line, thus corrupting the final image.
Restored the removed setting.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: saa7134: fix WARN_ON during resume

commit 30d652823de5fd7907d40e969a2d8e23938d8d03 upstream.

Do not attempt to reload the tuner modules when resuming after a suspend.
This triggers a WARN_ON in kernel/kmod.c:148 __request_module.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69581.

This has always been wrong, but it was never noticed until the WARN_ON
was added in 3.9.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: em28xx: fix PCTV 290e LNA oops

commit 3ec40dcfb413214b2874aec858870502b61c2202 upstream.

Pointer to device state has been moved to different location during
some change. PCTV 290e LNA function still uses old pointer, carried
over FE priv, and it crash.

Reported-by: Janne Kujanpää <jikuja@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: m88rs2000: add caps FE_CAN_INVERSION_AUTO

commit 3c8023a782964c72574ad8268ba0ea4e2d9772fc upstream.

The m88rs2000 frontend is always auto inversion.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: m88rs2000: prevent frontend crash on continuous transponder scans

commit 8272d0a0c0d374a01721e579df6e8add5577132b upstream.

Add m88rs2000_get_tune_settings, min delay of 2000 ms on symbol
rate more than 3000000 and delay of 3000ms less than this.

Adding min delay prevents crashing the frontend on continuous
transponder scans. Other dvb_frontend_tune_settings remain as default.

This makes very little time difference to good channel scans, but slows down
the set frontend where lock can never be achieved i.e. DVB-S2.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: v4l2-compat-ioctl32: fix wrong VIDIOC_SUBDEV_G/S_EDID32 support

commit bc826d6e39fe5f09cbadf8723e9183e6331b586f upstream.

The wrong ioctl numbers were used due to a copy-and-paste error.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: v4l2-dv-timings: add module name, description, license

commit c4885ada88e4331f8ac56d14296d0058359db2d7 upstream.

I completely forgot to add them when I made this module. Loading this module
without it will taint the kernel, which is not intended.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

video: atmel_lcdfb: ensure the hardware is initialized with the correct mode

commit 7d3477d801808a5037a511cf5a5aae5718e7ecce upstream.

If no driver takeover the atmel_lcdfb, the lcd won't be in a working state
since atmel_lcdfb_set_par() will never be called. Enabling a driver which does,
like fbcon, will call the function and put atmel_lcdfb in a working state.

Fixes: b985172b328a (video: atmel_lcdfb: add device tree suport)
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: videodev2.h: add parenthesis around macro arguments

commit aee786acfc0a12bcd37a1c60f3198fb25cf7181a upstream.

bt->width should be (bt)->width, and same for the other fields.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

media: uvcvideo: Do not use usb_set_interface on bulk EP

commit b1e43f232698274871e1358c276d7b0242a7d607 upstream.

The UVC specification uses alternate setting selection to notify devices
of stream start/stop. This breaks when using bulk-based devices, as the
video streaming interface has a single alternate setting in that case,
making video stream start and video stream stop events to appear
identical to the device. Bulk-based devices are thus not well supported
by UVC.

The webcam built in the Asus Zenbook UX302LA ignores the set interface
request and will keep the video stream enabled when the driver tries to
stop it. If USB autosuspend is enabled the device will then be suspended
and will crash, requiring a cold reboot.

USB trace capture showed that Windows sends a CLEAR_FEATURE(HALT)
request to the bulk endpoint when stopping the stream instead of
selecting alternate setting 0. The camera then behaves correctly, and
thus seems to require that behaviour.

Replace selection of alternate setting 0 with clearing of the endpoint
halt feature at video stream stop for bulk-based devices. Let's refrain
from blaming Microsoft this time, as it's not clear whether this
Windows-specific but USB-compliant behaviour was specifically developed
to handle bulkd-based UVC devices, or if the camera just took advantage
of it.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM

commit 01bb59ebffdec314da8da66266edf29529372f9b upstream.

When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]

Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.

This warning has been in since 3.2 kernel and was
caused by commit 421aa841a134f6a743111cf44d0c6d3b45e3cf8c
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried

Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

xhci: Switch Intel Lynx Point ports to EHCI on shutdown.

commit c09ec25d3684cad74d851c0f028a495999591279 upstream.

The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.

This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc66ea36623dbc2757a24fc2c4ab41b016
"xhci: Fix spurious wakeups after S5 on Haswell"

Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

xhci: Prevent runtime pm from autosuspending during initialization

commit bcffae7708eb8352f44dc510b326541fe43a02a4 upstream.

xHCI driver has its own pci probe function that will call usb_hcd_pci_probe
to register its usb-2 bus, and then continue to manually register the
usb-3 bus. usb_hcd_pci_probe does a pm_runtime_put_noidle at the end and
might thus trigger a runtime suspend before the usb-3 bus is ready.

Prevent the runtime suspend by increasing the usage count in the
beginning of xhci_pci_probe, and decrease it once the usb-3 bus is
ready.

xhci-platform driver is not using usb_hcd_pci_probe to set up
busses and should not need to have it's usage count increased during probe.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: gadget: zero: Fix SuperSpeed enumeration for alternate setting 1

commit 9c1b70361e0b38e4acb8e62b54da66538cb77ff2 upstream.

It was impossible to enumerate on a SuperSpeed (XHCI) host
with alternate setting = 1 due to the wrongly set 'bMaxBurst'
field in the SuperSpeed Endpoint Companion descriptor.

Testcase:
<host> modprobe -r usbtest; modprobe usbtest alt=1
<device> modprobe g_zero
plug device to SuperSpeed port on the host.

Without this patch the host always complains like so
"usb 12-2: Not enough bandwidth for new device state.
 usb 12-2: Not enough bandwidth for altsetting 1"

Bug was introduced by commit cf9a08ae in v3.9

Fixes: cf9a08ae5aec (usb: gadget: convert source sink and loopback to
new function interface)

Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: gadget: atmel_usba: fix crashed during stopping when DEBUG is enabled

commit d8eb6c653ef6b323d630de3c5685478469e248bc upstream.

commit 511f3c5 (usb: gadget: udc-core: fix a regression during gadget driver
unbinding) introduced a crash when DEBUG is enabled.

The debug trace in the atmel_usba_stop function made the assumption that the
driver pointer passed in parameter was not NULL, but since the commit above,
such assumption was no longer always true.

This commit now uses the driver pointer stored in udc which fixes this
issue.

[ balbi@ti.com : improved commit log a bit ]

Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

usb: gadget: tcm_usb_gadget: stop format strings

commit aba37fd975f0dd58e025c99c2a79b61b20190831 upstream.

This makes sure that the name coming out of configfs cannot be used
accidentally as a format string.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

reiserfs: fix race in readdir

commit 01d8885785a60ae8f4c37b0ed75bdc96d0fc6a44 upstream.

jdm-20004 reiserfs_delete_xattrs: Couldn't delete all xattrs (-2)

The -ENOENT is due to readdir calling dir_emit on the same entry twice.

If the dir_emit callback sleeps and the tree is changed underneath us,
we won't be able to trust deh_offset(deh) anymore. We need to save
next_pos before we might sleep so we can find the next entry.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

x86/efi: Correct EFI boot stub use of code32_start

commit 7e8213c1f3acc064aef37813a39f13cbfe7c3ce7 upstream.

code32_start should point at the start of the protected mode code, and
*not* at the beginning of the bzImage. This is much easier to do in
assembly so document that callers of make_boot_params() need to fill out
code32_start.

The fallout from this bug is that we would end up relocating the image
but copying the image at some offset, resulting in what appeared to be
memory corruption.

Reported-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

target/tcm_fc: Fix use-after-free of ft_tpg

commit 2c42be2dd4f6586728dba5c4e197afd5cfaded78 upstream.

ft_del_tpg checks tpg->tport is set before unlinking the tpg from the
tport when the tpg is being removed. Set this pointer in ft_tport_create,
or the unlinking won't happen in ft_del_tpg and tport->tpg will reference
a deleted object.

This patch sets tpg->tport in ft_tport_create, because that's what
ft_del_tpg checks, and is the only way to get back to the tport to
clear tport->tpg.

The bug was occuring when:

- lport created, tport (our per-lport, per-provider context) is
  allocated.
  tport->tpg = NULL
- tpg created
- a PRLI is received. ft_tport_create is called, tpg is found and
  tport->tpg is set
- tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not
  set, tport->tpg is not cleared and points at freed memory
- Future calls to ft_tport_create return tport via first conditional,
  instead of searching for new tpg by calling ft_lport_find_tpg.
  tport->tpg is still invalid, and will access freed memory.

see https://bugzilla.redhat.com/show_bug.cgi?id=1071340

Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist

commit a1e1774c6dfa3a524dd8df51ca95185fe5ef3247 upstream.

When compiled with CONFIG_DEBUG_SG set, uninitialized SGL leads
to BUG() in compare_and_write_callback().

Signed-off-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug

commit d444edc679e7713412f243b792b1f964e5cff1e1 upstream.

This patch fixes a long-standing bug in iscsit_build_conn_drop_async_message()
where during ERL=2 connection recovery, a bogus conn_p pointer could
end up being used to send the ISCSI_OP_ASYNC_EVENT + DROPPING_CONNECTION
notifying the initiator that cmd->logout_cid has failed.

The bug was manifesting itself as an OOPs in iscsit_allocate_cmd() with
a bogus conn_p pointer in iscsit_build_conn_drop_async_message().

Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Reported-by: santosh kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

SCSI: arcmsr: upper 32 of dma address lost

commit e2c70425f05219b142b3a8a9489a622c736db39d upstream.

The original code always set the upper 32 bits to zero because it was
doing a shift of the wrong variable.

Fixes: 1a4f550a09f8 ('[SCSI] arcmsr: 1.20.00.15: add SATA RAID plus other fixes')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

SCSI: qla2xxx: fix error handling of qla2x00_mem_alloc()

commit b2a72ec32d0f499aaadf41264232517a12326df0 upstream.

qla2x00_mem_alloc() returns 1 on success and -ENOMEM on failure.  On the
one hand the caller assumes non-zero is success but on the other hand
the caller also assumes that it returns an error code.

I've fixed it to return zero on success and a negative error code on
failure.  This matches the documentation as well.

[jejb: checkpatch fix]
Fixes: e315cd28b9ef ('[SCSI] qla2xxx: Code changes for qla data structure refactoring')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ib_srpt: Use correct ib_sg_dma primitives

commit b076808051f2c80d38e03fb2f1294f525c7a446d upstream.

The code was incorrectly using sg_dma_address() and
sg_dma_len() instead of ib_sg_dma_address() and
ib_sg_dma_len().

This prevents srpt from functioning with the
Intel HCA and indeed will corrupt memory
badly.

Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Tested-by: Vinod Kumar <vinod.kumar@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

IB/qib: add missing braces in do_qib_user_sdma_queue_create()

commit 37a967651caf99dd267017023737bd442f5acb3d upstream.

Commit c804f07248895ff9c moved qib_assign_ctxt() to
do_qib_user_sdma_queue_create() but dropped the braces
around the statements.

This was spotted by coccicheck (coccinelle/spatch):

$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/

  CHECK   drivers/infiniband/hw/qib/qib_file_ops.c
drivers/infiniband/hw/qib/qib_file_ops.c:1583:2-23: code aligned with following code on line 1587

This patch adds braces back.

Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

IB/qib: Fix debugfs ordering issue with multiple HCAs

commit f8b6c47a44c063062317646683a73371c24c69ee upstream.

The debugfs init code was incorrectly called before the idr mechanism
is used to get the unit number, so the dd->unit hasn't been
initialized.  This caused the unit relative directory creation to fail
after the first.

This patch moves the init for the debugfs stuff until after all of the
failures and after the unit number has been determined.

A bug in unwind code in qib_alloc_devdata() is also fixed.

Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

IB/ehca: Returns an error on ib_copy_to_udata() failure

commit 5bdb0f02add5994b0bc17494f4726925ca5d6ba1 upstream.

In case of error when writing to userspace, function ehca_create_cq()
does not set an error code before following its error path.

This patch sets the error code to -EFAULT when ib_copy_to_udata()
fails.

This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().

Link: https://www.gitorious.org/opteya/coccib/source/75ebf2c1033c64c1d81df13e4ae44ee99c989eba:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

IB/mthca: Return an error on ib_copy_to_udata() failure

commit 08e74c4b00c30c232d535ff368554959403d0432 upstream.

In case of error when writing to userspace, the function mthca_create_cq()
does not set an error code before following its error path.

This patch sets the error code to -EFAULT when ib_copy_to_udata() fails.

This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().

Link: https://www.gitorious.org/opteya/coccib/source/75ebf2c1033c64c1d81df13e4ae44ee99c989eba:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

IB/nes: Return an error on ib_copy_from_udata() failure instead of NULL

commit 9d194d1025f463392feafa26ff8c2d8247f71be1 upstream.

In case of error while accessing to userspace memory, function
nes_create_qp() returns NULL instead of an error code wrapped through
ERR_PTR().  But NULL is not expected by ib_uverbs_create_qp(), as it
check for error with IS_ERR().

As page 0 is likely not mapped, it is going to trigger an Oops when
the kernel will try to dereference NULL pointer to access to struct
ib_qp's fields.

In some rare cases, page 0 could be mapped by userspace, which could
turn this bug to a vulnerability that could be exploited: the function
pointers in struct ib_device will be under userspace total control.

This was caught when using spatch (aka. coccinelle)
to rewrite calls to ib_copy_{from,to}_udata().

Link: https://www.gitorious.org/opteya/ib-hw-nes-create-qp-null
Link: https://www.gitorious.org/opteya/coccib/source/75ebf2c1033c64c1d81df13e4ae44ee99c989eba:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

IB/ipath: Fix potential buffer overrun in sending diag packet routine

commit a2cb0eb8a64adb29a99fd864013de957028f36ae upstream.

Guard against a potential buffer overrun.  The size to read from the
user is passed in, and due to the padding that needs to be taken into
account, as well as the place holder for the ICRC it is possible to
overflow the 32bit value which would cause more data to be copied from
user space than is allocated in the buffer.

Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd: set timeparms.to_maxval in setup_callback_client

commit 3758cf7e14b753838fe754ede3862af10b35fdac upstream.

...otherwise the logic in the timeout handling doesn't work correctly.

Spotted-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

NFSD: Traverse unconfirmed client through hash-table

commit 2b9056359889c78ea5decb5b654a512c2e8a945c upstream.

When stopping nfsd, I got BUG messages, and soft lockup messages,
The problem is cuased by double rb_erase() in nfs4_state_destroy_net()
and destroy_client().

This patch just let nfsd traversing unconfirmed client through
hash-table instead of rbtree.

[ 2325.021995] BUG: unable to handle kernel NULL pointer dereference at
          (null)
[ 2325.022809] IP: [<ffffffff8133c18c>] rb_erase+0x14c/0x390
[ 2325.022982] PGD 7a91b067 PUD 7a33d067 PMD 0
[ 2325.022982] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 2325.022982] Modules linked in: nfsd(OF) cfg80211 rfkill bridge stp
llc snd_intel8x0 snd_ac97_codec ac97_bus auth_rpcgss nfs_acl serio_raw
e1000 i2c_piix4 ppdev snd_pcm snd_timer lockd pcspkr joydev parport_pc
snd parport i2c_core soundcore microcode sunrpc ata_generic pata_acpi
[last unloaded: nfsd]
[ 2325.022982] CPU: 1 PID: 2123 Comm: nfsd Tainted: GF          O
3.14.0-rc8+ #2
[ 2325.022982] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS
VirtualBox 12/01/2006
[ 2325.022982] task: ffff88007b384800 ti: ffff8800797f6000 task.ti:
ffff8800797f6000
[ 2325.022982] RIP: 0010:[<ffffffff8133c18c>]  [<ffffffff8133c18c>]
rb_erase+0x14c/0x390
[ 2325.022982] RSP: 0018:ffff8800797f7d98  EFLAGS: 00010246
[ 2325.022982] RAX: ffff880079c1f010 RBX: ffff880079f4c828 RCX:
0000000000000000
[ 2325.022982] RDX: 0000000000000000 RSI: ffff880079bcb070 RDI:
ffff880079f4c810
[ 2325.022982] RBP: ffff8800797f7d98 R08: 0000000000000000 R09:
ffff88007964fc70
[ 2325.022982] R10: 0000000000000000 R11: 0000000000000400 R12:
ffff880079f4c800
[ 2325.022982] R13: ffff880079bcb000 R14: ffff8800797f7da8 R15:
ffff880079f4c860
[ 2325.022982] FS:  0000000000000000(0000) GS:ffff88007f900000(0000)
knlGS:0000000000000000
[ 2325.022982] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 2325.022982] CR2: 0000000000000000 CR3: 000000007a3ef000 CR4:
00000000000006e0
[ 2325.022982] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[ 2325.022982] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[ 2325.022982] Stack:
[ 2325.022982]  ffff8800797f7de0 ffffffffa0191c6e ffff8800797f7da8
ffff8800797f7da8
[ 2325.022982]  ffff880079f4c810 ffff880079bcb000 ffffffff81cc26c0
ffff880079c1f010
[ 2325.022982]  ffff880079bcb070 ffff8800797f7e28 ffffffffa01977f2
ffff8800797f7df0
[ 2325.022982] Call Trace:
[ 2325.022982]  [<ffffffffa0191c6e>] destroy_client+0x32e/0x3b0 [nfsd]
[ 2325.022982]  [<ffffffffa01977f2>] nfs4_state_shutdown_net+0x1a2/0x220
[nfsd]
[ 2325.022982]  [<ffffffffa01700b8>] nfsd_shutdown_net+0x38/0x70 [nfsd]
[ 2325.022982]  [<ffffffffa017013e>] nfsd_last_thread+0x4e/0x80 [nfsd]
[ 2325.022982]  [<ffffffffa001f1eb>] svc_shutdown_net+0x2b/0x30 [sunrpc]
[ 2325.022982]  [<ffffffffa017064b>] nfsd_destroy+0x5b/0x80 [nfsd]
[ 2325.022982]  [<ffffffffa0170773>] nfsd+0x103/0x130 [nfsd]
[ 2325.022982]  [<ffffffffa0170670>] ? nfsd_destroy+0x80/0x80 [nfsd]
[ 2325.022982]  [<ffffffff810a8232>] kthread+0xd2/0xf0
[ 2325.022982]  [<ffffffff810a8160>] ? insert_kthread_work+0x40/0x40
[ 2325.022982]  [<ffffffff816c493c>] ret_from_fork+0x7c/0xb0
[ 2325.022982]  [<ffffffff810a8160>] ? insert_kthread_work+0x40/0x40
[ 2325.022982] Code: 48 83 e1 fc 48 89 10 0f 84 02 01 00 00 48 3b 41 10
0f 84 08 01 00 00 48 89 51 08 48 89 fa e9 74 ff ff ff 0f 1f 40 00 48 8b
50 10 <f6> 02 01 0f 84 93 00 00 00 48 8b 7a 10 48 85 ff 74 05 f6 07 01
[ 2325.022982] RIP  [<ffffffff8133c18c>] rb_erase+0x14c/0x390
[ 2325.022982]  RSP <ffff8800797f7d98>
[ 2325.022982] CR2: 0000000000000000
[ 2325.022982] ---[ end trace 28c27ed011655e57 ]---

[  228.064071] BUG: soft lockup - CPU#0 stuck for 22s! [nfsd:558]
[  228.064428] Modules linked in: ip6t_rpfilter ip6t_REJECT cfg80211
xt_conntrack rfkill ebtable_nat ebtable_broute bridge stp llc
ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6
nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw
ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4
nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security
iptable_raw nfsd(OF) auth_rpcgss nfs_acl lockd snd_intel8x0
snd_ac97_codec ac97_bus joydev snd_pcm snd_timer e1000 sunrpc snd ppdev
parport_pc serio_raw pcspkr i2c_piix4 microcode parport soundcore
i2c_core ata_generic pata_acpi
[  228.064539] CPU: 0 PID: 558 Comm: nfsd Tainted: GF          O
3.14.0-rc8+ #2
[  228.064539] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS
VirtualBox 12/01/2006
[  228.064539] task: ffff880076adec00 ti: ffff880074616000 task.ti:
ffff880074616000
[  228.064539] RIP: 0010:[<ffffffff8133ba17>]  [<ffffffff8133ba17>]
rb_next+0x27/0x50
[  228.064539] RSP: 0018:ffff880074617de0  EFLAGS: 00000282
[  228.064539] RAX: ffff880074478010 RBX: ffff88007446f860 RCX:
0000000000000014
[  228.064539] RDX: ffff880074478010 RSI: 0000000000000000 RDI:
ffff880074478010
[  228.064539] RBP: ffff880074617de0 R08: 0000000000000000 R09:
0000000000000012
[  228.064539] R10: 0000000000000001 R11: ffffffffffffffec R12:
ffffea0001d11a00
[  228.064539] R13: ffff88007f401400 R14: ffff88007446f800 R15:
ffff880074617d50
[  228.064539] FS:  0000000000000000(0000) GS:ffff88007f800000(0000)
knlGS:0000000000000000
[  228.064539] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  228.064539] CR2: 00007fe9ac6ec000 CR3: 000000007a5d6000 CR4:
00000000000006f0
[  228.064539] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[  228.064539] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[  228.064539] Stack:
[  228.064539]  ffff880074617e28 ffffffffa01ab7db ffff880074617df0
ffff880074617df0
[  228.064539]  ffff880079273000 ffffffff81cc26c0 ffffffff81cc26c0
0000000000000000
[  228.064539]  0000000000000000 ffff880074617e48 ffffffffa01840b8
ffffffff81cc26c0
[  228.064539] Call Trace:
[  228.064539]  [<ffffffffa01ab7db>] nfs4_state_shutdown_net+0x18b/0x220
[nfsd]
[  228.064539]  [<ffffffffa01840b8>] nfsd_shutdown_net+0x38/0x70 [nfsd]
[  228.064539]  [<ffffffffa018413e>] nfsd_last_thread+0x4e/0x80 [nfsd]
[  228.064539]  [<ffffffffa00aa1eb>] svc_shutdown_net+0x2b/0x30 [sunrpc]
[  228.064539]  [<ffffffffa018464b>] nfsd_destroy+0x5b/0x80 [nfsd]
[  228.064539]  [<ffffffffa0184773>] nfsd+0x103/0x130 [nfsd]
[  228.064539]  [<ffffffffa0184670>] ? nfsd_destroy+0x80/0x80 [nfsd]
[  228.064539]  [<ffffffff810a8232>] kthread+0xd2/0xf0
[  228.064539]  [<ffffffff810a8160>] ? insert_kthread_work+0x40/0x40
[  228.064539]  [<ffffffff816c493c>] ret_from_fork+0x7c/0xb0
[  228.064539]  [<ffffffff810a8160>] ? insert_kthread_work+0x40/0x40
[  228.064539] Code: 1f 44 00 00 55 48 8b 17 48 89 e5 48 39 d7 74 3b 48
8b 47 08 48 85 c0 75 0e eb 25 66 0f 1f 84 00 00 00 00 00 48 89 d0 48 8b
50 10 <48> 85 d2 75 f4 5d c3 66 90 48 3b 78 08 75 f6 48 8b 10 48 89 c7

Fixes: ac55fdc408039 (nfsd: move the confirmed and unconfirmed hlists...)
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd4: fix setclientid encode size

commit 480efaee085235bb848f1063f959bf144103c342 upstream.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd: check passed socket's net matches NFSd superblock's one

commit 3064639423c48d6e0eb9ecc27c512a58e38c6c57 upstream.

There could be a case, when NFSd file system is mounted in network, different
to socket's one, like below:

"ip netns exec" creates new network and mount namespace, which duplicates NFSd
mount point, created in init_net context. And thus NFS server stop in nested
network context leads to RPCBIND client destruction in init_net.
Then, on NFSd start in nested network context, rpc.nfsd process creates socket
in nested net and passes it into "write_ports", which leads to RPCBIND sockets
creation in init_net context because of the same reason (NFSd monut point was
created in init_net context). An attempt to register passed socket in nested
net leads to panic, because no RPCBIND client present in nexted network
namespace.

This patch add check that passed socket's net matches NFSd superblock's one.
And returns -EINVAL error to user psace otherwise.

v2: Put socket on exit.

Reported-by: Weng Meiling <wengmeiling.weng@huawei.com>
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd: notify_change needs elevated write count

commit 9f67f189939eccaa54f3d2c9cf10788abaf2d584 upstream.

Looks like this bug has been here since these write counts were
introduced, not sure why it was just noticed now.

Thanks also to Jan Kara for pointing out the problem.

Reported-by: Matthew Rahtz <mrahtz@rapitasystems.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd4: leave reply buffer space for failed setattr

commit 04819bf6449094e62cebaf5199d85d68d711e667 upstream.

This fixes an ommission from 18032ca062e621e15683cb61c066ef3dc5414a7b
"NFSD: Server implementation of MAC Labeling", which increased the size
of the setattr error reply without increasing COMPOUND_ERR_SLACK_SPACE.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd4: fix test_stateid error reply encoding

commit a11fcce1544df08c723d950ff0edef3adac40405 upstream.

If the entire operation fails then there's nothing to encode.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd4: buffer-length check for SUPPATTR_EXCLCREAT

commit de3997a7eeb9ea286b15879fdf8a95aae065b4f7 upstream.

This was an omission from 8c18f2052e756e7d5dea712fc6e7ed70c00e8a39
"nfsd41: SUPPATTR_EXCLCREAT attribute".

Cc: Benny Halevy <bhalevy@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

nfsd4: session needs room for following op to error out

commit 4c69d5855a16f7378648c5733632628fa10431db upstream.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

NFSv4: Fix a use-after-free problem in open()

commit e911b8158ee1def8153849b1641b736026b036e0 upstream.

If we interrupt the nfs4_wait_for_completion_rpc_task() call in
nfs4_run_open_task(), then we don't prevent the RPC call from
completing. So freeing up the opendata->f_attr.mdsthreshold
in the error path in _nfs4_do_open() leads to a use-after-free
when the XDR decoder tries to decode the mdsthreshold information
from the server.

Fixes: 82be417aa37c0 (NFSv4.1 cache mdsthreshold values on OPEN)
Tested-by: Steve Dickson <SteveD@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

iio: querying buffer scan_mask should return 0/1

commit 2076a20fc1a06f7b0333c62a2bb4eeeac7ed1bcb upstream.

Ensure that querying the IIO buffer scan_mask returns a value of
0 or 1. Currently querying the scan mask has the value returned
by test_bit(), which returns either true or false. For some
architectures test_bit() may return -1 for true, which will appear
to return an error when returning from iio_scan_mask_query().

Additionally, it's important for the sysfs interface to consistently
return the same thing when querying the scan_mask.

Signed-off-by: Alec Berg <alecaberg@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

USB: fix crash during hotplug of PCI USB controller card

commit a2ff864b53eac9a0e9b05bfe9d1781ccd6c2af71 upstream.

The code in hcd-pci.c that matches up EHCI controllers with their
companion UHCI or OHCI controllers assumes that the private drvdata
fields don't get set too early.  However, it turns out that this field
gets set by usb_create_hcd(), before hcd-pci expects it, and this can
result in a crash when two controllers are probed in parallel (as can
happen when a new controller card is hotplugged).

The companions_rwsem lock was supposed to prevent this sort of thing,
but usb_create_hcd() is called outside the scope of the rwsem.

A simple solution is to check that the root-hub pointer has been
initialized as well as the drvdata field.  This doesn't happen until
usb_add_hcd() is called; that call and the check are both protected by
the rwsem.

This patch should be applied to stable kernels from 3.10 onward.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stefani Seibold <stefani@seibold.net>
Tested-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

PCI: mvebu: Fix potential issue in range parsing

commit 4f4bde1df33bde076f53325bdf2c6430cf85e1bb upstream.

The second parameter of of_read_number() is not the index, but a size.  As
it happens, in this case it may work just fine because of the conversion to
u32 and the favorable endianness on this architecture.

Fixes: 11be65472a427 ("PCI: mvebu: Adapt to the new device tree layout")
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

regulator: arizona-ldo1: Correct default regulator init_data

commit a35ff2861690eaf9dbb38fa744a8a9e6f4ebfd61 upstream.

Both 5102 and 8997 have the regulator capable of supplying 1.8V, and the
voltage step from the 5110 regulator is different from what is specified
in the default description. This patch updates the default regulator
description to match 5110 and selects the 1.8V capable description for
8997.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels

commit b3b42ac2cbae1f3cecbb6229964a4d48af31d382 upstream.

The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer.  We have
a software workaround for that ("espfix") for the 32-bit kernel, but
it relies on a nonzero stack segment base which is not available in
32-bit mode.

Since 16-bit support is somewhat crippled anyway on a 64-bit kernel
(no V86 mode), and most (if not quite all) 64-bit processors support
virtualization for the users who really need it, simply reject
attempts at creating a 16-bit segment when running on top of a 64-bit
kernel.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-kicdm89kzw9lldryb1br9od0@git.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ftrace/x86: One more missing sync after fixup of function modification failure

commit 12729f14d8357fb845d75155228b21e76360272d upstream.

If a failure occurs while modifying ftrace function, it bails out and will
remove the tracepoints to be back to what the code originally was.

There is missing the final sync run across the CPUs after the fix up is done
and before the ftrace int3 handler flag is reset.

Here's the description of the problem:

CPU0 CPU1
---- ----
  remove_breakpoint();
  modifying_ftrace_code = 0;

[still sees breakpoint]
<takes trap>
[sees modifying_ftrace_code as zero]
[no breakpoint handler]
[goto failed case]
[trap exception - kernel breakpoint, no
 handler]
BUG()

Link: http://lkml.kernel.org/r/1393258342-29978-2-git-send-email-pmladek@suse.cz
Fixes: 8a4d0a687a5 "ftrace: Use breakpoint method to update ftrace caller"
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL

commit 9452bf560273e4de2395ffdd79024debfb0c1290 upstream.

This makes the follow-on check for psta != NULL pointless and makes
the whole exercise rather pointless. This is another case of why
blindly zero-initializing variables when they are declared is bad.

Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

staging: comedi: usbdux: bug fix for accessing 'ao_chanlist' in private data

commit 2704f807f9498054b8153002bafa3e818079e9a5 upstream.

In usbdux_ao_cmd(), the channels for the command are transfered from the
cmd->chanlist and stored in the private data 'ao_chanlist'. The channel
numbers are bit-shifted when stored so that they become the "command"
that is transfered to the device. The channel to command conversion
results in the 'ao_chanlist' having these values for the channels:

  channel 0 -> ao_chanlist = 0x00
  channel 1 -> ao_chanlist = 0x40
  channel 2 -> ao_chanlist = 0x80
  channel 3 -> ao_chanlist = 0xc0

The problem is, the usbduxsub_ao_isoc_irq() function uses the 'chan' value
from 'ao_chanlist' to access the 'ao_readback' array in the private data.
So instead of accessing the array as 0, 1, 2, 3, it accesses it as 0x00,
0x40, 0x80, 0xc0.

Fix this by storing the raw channel number in 'ao_chanlist' and doing the
bit-shift when creating the command.

Fixes: a998a3db530bff80 "staging: comedi: usbdux: cleanup the private data 'outBuffer'"
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Acked-by: Bernd Porr <mail@berndporr.me.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0

commit f764cd68d9036498f08fe8834deb6a367b5c2542 upstream.

Zero-initializing ether_type masked that the ether type would never be
obtained for 8021x packets and the comparison against eapol_type
would always fail.

Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

staging:serqt_usb2: Fix sparse warning restricted __le16 degrades to integer

commit abe5d64d1a74195a44cd14624f8178b9f48b7cc7 upstream.

This patch fixes the following sparse warning :
drivers/staging/serqt_usb2/serqt_usb2.c:727:40: warning: restricted __le16 degrades to integer

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

w1: fix w1_send_slave dropping a slave id

commit 6b355b33a64fd6d8ead2b838ec16fb9b551f71e8 upstream.

Previous logic,
if (avail > 8) {
store slave;
return;
}
send data; clear;

The logic error is, if there isn't space send the buffer and clear,
but the slave wasn't added to the now empty buffer loosing that slave
id.  It also should have been "if (avail >= 8)" because when it is 8,
there is space.

Instead, if there isn't space send and clear the buffer, then there is
always space for the slave id.

Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: kempld-core: Fix potential hang-up during boot

commit 204747c970c0d568721c76ab8a57dde0e5dcf0d5 upstream.

On PXT and COMe-cPC2 boards it is observed that the hardware
mutex is acquired but not being released during initialization.
This can result in a hang-up during boot if the driver is built
into the kernel.

Releasing the mutex twice if it was acquired fixes the problem.
Subsequent request/release cycles work as expected, so the fix is
only needed during initialization.

Reviewed-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: tps65910: Fix possible invalid pointer dereference on regmap_add_irq_chip fail

commit 483e2dfdbc94751430e41db9973985f5b054d322 upstream.

Fixes: 4aab3fadad32 ("mfd: tps65910: Move interrupt implementation code to mfd file")
tps65910_irq_init() sets 'tps65910->chip_irq' before calling
regmap_add_irq_chip(). If the regmap_add_irq_chip() call fails in
memory allocation of regmap_irq_chip_data members then:

1. The 'tps65910->chip_irq' will still hold some value
2. 'tps65910->irq_data' will be pointing to already freed memory
   (because regmap_add_irq_chip() will free it on error)

This results in invalid memory access during driver remove because the
tps65910_irq_exit() tests whether 'tps65910->chip_irq' is not zero.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: max8997: Fix possible NULL pointer dereference on i2c_new_dummy error

commit 97dc4ed3fa377ec91bb60ba98b70d645c2099384 upstream.

During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this
calls.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: max8998: Fix possible NULL pointer dereference on i2c_new_dummy error

commit ed26f87b9f71693a1d1ee85f5e6209601505080f upstream.

During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: max8925: Fix possible NULL pointer dereference on i2c_new_dummy error

commit 96cf3dedc491d2f1f66cc26217f2b06b0c7b6797 upstream.

During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this
calls.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: max77693: Fix possible NULL pointer dereference on i2c_new_dummy error

commit ad09dd6a1f5d6244bd89314015af506ba7f9810a upstream.

During probe the driver allocates dummy I2C devices for MUIC and haptic
with i2c_new_dummy() but it does not check the return value of this
calls.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by devm_regmap_init_i2c() and i2c_unregister_device().

If i2c_new_dummy() fails for MUIC or haptic devices, fail also the probe
for main MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: max77686: Fix possible NULL pointer dereference on i2c_new_dummy error

commit b9e183a1d495cd65412abe0f9df19b151716bfe7 upstream.

During probe the driver allocates dummy I2C device for RTC with
i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: 88pm800: Fix I2C device resource leak if probe fails

commit 141050cf3d84fc303df58796d68dc1376b0e8f67 upstream.

During probe the driver allocates two dummy I2C devices for subchips in
function pm800_pages_init(). Additionally this function allocates
regmaps for these subchips. If any of these steps fail then these dummy
I2C devices are not freed and resources leak.

On pm800_pages_init() fail the driver must call pm800_pages_exit() to
unregister dummy I2C devices.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: 88pm860x: Fix I2C device resource leak on regmap init fail

commit a7ab1c8b261305af583ce26bb4a14f555fdaa73e upstream.

During probe the driver allocates dummy I2C device for companion chip
and then allocates a regmap for it. If regmap_init_i2c() fails then the
I2C driver (allocated with i2c_new_dummy()) is not freed and this
resource leaks.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: 88pm860x: Fix possible NULL pointer dereference on i2c_new_dummy error

commit 159ce52a6b777fc82fa0b51c7440e25f9e4c6feb upstream.

During probe the driver allocates dummy I2C device for companion chip
with i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by regmap_init_i2c().

If i2c_new_dummy() fails for companion device, fail also the probe for
main MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mfd: sec-core: Fix possible NULL pointer dereference when i2c_new_dummy error

commit 65aba1e04916d72b30c028730a1e31860c225412 upstream.

During probe the sec-core driver allocates dummy I2C device for RTC with
i2c_new_dummy() but return value is not checked. In case of error
(i2c_new_device(): memory allocation failure or I2C address cannot be
used) this function returns NULL which is later used by
devm_regmap_init_i2c() or i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for main
MFD driver.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mei: ignore client writing state during cb completion

commit 34ec43661fe8f1977dd0f05353302ae2ed10aabb upstream.

Ignore client writing state during cb completion to fix a memory
leak.

When moving cbs to the completion list we should not look at
writing_state as this state can be already overwritten by next
write, the fact that a cb is on the write waiting list means
that it was already written to the HW and we can safely complete it.

Same pays for wait in poll handler, we do not have to check the state
wake is done after completion list processing.

Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mei: me: do not load the driver if the FW doesn't support MEI interface

commit 5e6533a6f52f1a8283b2f818f5828be99a417dd6 upstream.

NM and SPS  FW types that may run on ME device on server platforms
do not have valid MEI/HECI interface and driver should not
be bound to it as this might lead to system hung.
In practice not all BIOSes effectively hide such devices from the
OS and in some cases it is not possible.

We determine FW type by examining Host FW status registers in order to
unbind the driver.
In this patch we are adding check for ME on Cougar Point, Lynx Point
Devices

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

mei: fix memory leak of pending write cb objects

commit cc99ecfdac01215594c73907726b12f251c21e20 upstream.

Write callbacks are released on the write completed path but
when file handler is closed before the writes are
completed those are left dangling on write and write_waiting queues.

We add mei_io_list_free function to perform this task

Also move static functions to client.c form client.h

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

KVM: s390: Optimize ucontrol path

commit 2955c83f72801245afd0fe5c560cc75b82bea9aa upstream.

Since commit 7c470539c95630c1f2a10f109e96f249730b75eb
(s390/kvm: avoid automatic sie reentry) we will run through the C code
of KVM on host interrupts instead of just reentering the guest. This
will result in additional ucontrol exits (at least HZ per second). Let
handle a 0 intercept in the kernel and dont return to userspace,
even if in ucontrol mode.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

s390/cio: fix driver callback initialization for ccw consoles

commit 2253e8d79237c69086ded391e6767afe16972527 upstream.

ccw consoles are in use before they can be properly registered with
the driver core. For devices which are in use by a device driver we
rely on the ccw_device's pointer to the driver callbacks to be valid.
For ccw consoles this pointer is NULL until they are registered later
during boot and we dereferenced this pointer. This worked by
chance on 64 bit builds (cdev->drv was NULL but the optional callback
cdev->drv->path_event was also NULL by coincidence) and was unnoticed
until we received reports about boot failures on 31 bit systems.
Fix it by initializing the driver pointer for ccw consoles.

Reported-by: Mike Frysinger <vapier@gentoo.org>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

spi: efm32: use $vendor,$device scheme for compatible string

commit 12f6dd860cf8bf036c0bec38c00a53da71bcd43a upstream.

Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ACPICA: Restore code that repairs NULL package elements in return values.

commit 61db45ca21630f5ab7f678d54c5d969c21647854 upstream.

The original code was lost accidently, it was not generated along with the
following commit of mechanism improvements and thus not get merged:

  Commit: d5a36100f62fa6db5541344e08b361b34e9114c5
  Subject: ACPICA: Add mechanism for early object repairs on a per-name basis

  Adds the framework to allow object repairs very early in the
  return object analysis. Enables repairs like string->unicode,
  etc.

This patch restores the implementation of the NULL element repair code for
ACPI_RTYPE_NONE.  In the original design, ACPI_RTYPE_NONE is defined to
collect simple NULL object repairs.
Lv Zheng.

Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=67901
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ALSA: hda/realtek - Add headset Mic support for Dell machine

commit 8dc9abb93dde94e7f2bc719032fe16f5713df05c upstream.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ALSA: hda/realtek - Add support of ALC288 codec

commit 7c66593286bcd153e4868383e675673a27071bd5 upstream.

Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ALSA: hda - Fix silent speaker output due to mute LED fixup

commit 415d555e6b398b00fc1733f0113065a54df9106a upstream.

The recent fixups for HP laptops to support the mute LED made the
speaker output silent on some machines.  It turned out that they use
the NID 0x18 for the speaker while it's also used for controlling the
LED via VREF bits although the current driver code blindly assumes
that such a node is a mic pin (where 0x18 is usually so).

This patch fixes the problem by only changing the VREF bits and
keeping the other pin ctl bits.

Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ALSA: ice1712: Fix boundary checks in PCM pointer ops

commit 4f8e940095536bc002a81666a4107a581c84e9b9 upstream.

PCM pointer callbacks in ice1712 driver check the buffer size boundary
wrongly between bytes and frames.  This leads to PCM core warnings
like:
   snd_pcm_update_hw_ptr0: 105 callbacks suppressed
   ALSA pcm_lib.c:352 BUG: pcmC3D0c:0, pos = 5461, buffer size = 5461, period size = 2730

This patch fixes these checks to be placed after the proper unit
conversions.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

ALSA: hda - Enable beep for ASUS 1015E

commit a4b7f21d7b42b33609df3f86992a8deff80abfaf upstream.

The `lspci -nnvv` output contains (wrapped for line length):

  00:1b.0 Audio device [0403]:
    Intel Corporation 7 Series/C210 Series Chipset Family
    High Definition Audio Controller [8086:1e20] (rev 04)
        Subsystem: ASUSTeK Computer Inc. Device [1043:115d]

Signed-off-by: W. Trevor King <wking@tremily.us>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>